Industry News

Joe Molter

The author is president of the West Chester Amateur Radio Association (WCARA), a division of the National Voice of America Museum of Broadcasting dedicated to advancing the amateur radio hobby. He’s also a volunteer-at-large at the museum. His call sign is N81DA.

Her six massive transmitters may be quiet, but she is far from silent.

Amateur radio operators routinely talk to the world from station WC8VOA in West Chester, Ohio, located about 25 miles north of Cincinnati. This former VOA relay station is now the National VOA Museum of Broadcasting with collections from the Gray History of Wireless Museum; Powel Crosley Jr., and Cincinnati radio and TV broadcasting history; and the Voice of America. Next week the museum celebrates the 75th anniversary of the Bethany Station Saturday, Sept. 21, with a fundraiser to make the first floor of the museum accessible for people for all abilities.

The National Voice of America Museum of Broadcasting is open every weekend from 1 to 4 p.m. Tours are given continuously on weekend afternoons by knowledgeable docents. It houses the Bethany station’s last control room and one of the remaining 250 kW Collins shortwave transmitters.

You can sit at the massive audio console that controlled the six shortwave transmitters and literally take a tour inside one of the Collins transmitters. You can view the massive switch gear, built during World War II, which changed Bethany’s 24 rhombic antennas to its six transmitters.

At one time Bethany Station covered a square mile of property that was once farmland. Today the museum sits on 14 acres and the antennas are gone, but with surrounding park acreage, you get a sense of the massive scale the site covered with towers and the miles of transmission lines and antenna wire.

The museum houses a large collection of radios from the early part of the twentieth century, including names such as Hallicrafters, National, Drake and Collins. A large collection of Drake amateur radio products is always a must-see by visiting radio enthusiasts and ham radio operators.

Drake radios were produced nearby in Miamisburg, Ohio. An area dedicated to the Crosley Corp. shows off many of the Crosley brothers’ radio, TV and household products that were manufactured in Cincinnati. Crosley contributed heavily to the war effort during World War II, with the production of tens of thousands of portable radios for the U.S. Army and millions of proximity fuses for antiaircraft ordinance.

Not only did Crosley develop radios, but content as well, with its on-air radio station WLW, which still broadcasts today on 700 AM. WLW transmits from its original site and the large Blaw-Knox tower can be seen from the VOA museum. The museum contains the original 50 W AM transmitter that WLW started with in 1922.

Bethany VOA Towers at Sunset. Photo Andrew Albrecht

WLW was the only U.S. station allowed to operate at 500,000 watts of power during the 1930s. The collection includes a bright red Crosley Hot Shot sports car, too. Crosley Corp. developed a number of vehicles during the late 1930s and resumed production after World War II until shutting down in 1952.

An additional area of the museum houses artifacts and memorabilia from the early era of Cincinnati radio and TV broadcasting. The Cincinnati Media Heritage section includes many of the celebrities who got their start at WLW and other local broadcasting outlets. These WLW radio stars — many of whom transitioned from radio to TV—include Rod Serling of “Twilight Zone” fame; sisters Rosemary and Betty Clooney; Eddie Albert; Doris Day; The Mills Brothers; and Ruth Lyons.

Housed in three of Bethany’s old transmitter vaults, the history of broadcasting section showcases the talent and equipment that made Cincinnati an early nursery for radio and television entertainment. Artifacts include equipment from a 1930s radio station; a 1950s AM station, including disc jockey’s audio console and turntables; and a 1,000 W transmitter. A very early and massive RCA Victor color television camera is on display, along with other television and video equipment.

Our amateur radio station is operated under FCC license WC8VOA and is manned by the West Chester Amateur Radio Association. The station has seven operating positions equipped with modern and vintage amateur radio gear. Antennas cover the radio spectrum from two meters down to 160 meters. The former VOA receiving satellite dish has been converted to 10 GHz transmit and receive capabilities for EME (Earth Moon Earth) bounce. Signals are sent to the moon and the dish used as a passive satellite to communicate with other amateur radio operators.

The club participates in radio contests, portable operations and local STEM events. It averages some 6,000 contacts per year, covering modes of voice and digital and CW. The club also operates two FM repeaters on two meters and 440 MHz.

Operators are in the shack every weekend and hold an open house every Wednesday night for radio enthusiasts and those interested in obtaining a ham radio license. Our WC8VOA call sign is recognized by many of our fellow radio amateurs around the world. We have made contacts from all seven continents and hundreds of countries.

Radio is still an important part of our lives; whether it is listening to AM, FM or satellite services, radio remains a viable source of our news and entertainment.

Voice of America broadcasts were never intended for Americans. They were targeted to people living in oppressed countries where media was censored with the intention to change people’s minds by providing sourced and accurate news. In fact, the VOA Charter (Public Law 94-350), which was passed in 1976, during from the Pres. Gerald Ford administration, states that VOA news will be” accurate, objective, and comprehensive.” It will also “represent America, not any single segment of American society, and will therefore present a balanced and comprehensive projection of significant American thought and institutions.” Lastly, the VOA is mandated to “present the policies of the United States clearly and effectively and will also present responsible discussions and opinion on these policies.”

VOA news and feature stories are still broadcast and transmitted today to more than 275 million people weekly in 40+ languages in nearly 100 countries. VOA programs are delivered on multiple platforms, including radio, television, web and mobile via a network of more than 3,000 media outlets worldwide.

Broadcasts have aired continually for more than 75 years, along with sister stations of Radio Free Europe; Radio Liberty; Radio Free Asia; and Radio Marti.

Here is the crux of the matter for all of us at the VOA museum: Once Bethany Station began operation during mid-World War II, an infuriated Adolf Hitler was quoted as saying on one of his radio broadcasts to never listen to those “Cincinnati Liars.” We’re proud to be part of the VOA heritage we are entrusted with and even more proud to be related to those “liars” from Cincinnati.

VOA Bethany in Fog

But while we’re proud of our heritage, I must be honest. The museum is housed in an aging, uninsulated, 75-year-old building that constantly needs repairs. We receive no federal funding and this is our big fundraising push for the year. Our workforce of docents, conservators and maintenance crews are all unpaid volunteers. And many of our volunteers come from our local radio club, the West Chester Amateur Radio Association.

Please help us out with a donation; better yet, plan a long weekend vacation and come on out to West Chester for our Sept. 21 fundraiser! We include a friendly community of shortwave radio aficionados always eager to make more friends. We’ll have on hand auction and silent auction items; dinner-by-the-bite; museum tours; and a table-to-table Trivial Pursuit game, all with the relaxing strains of jazz in the background.

For information on the museum and how you can help with donations, visit our website. Please purchase tickets or donate today. If you’re interested in our amateur radio group, additional information is at West Chester Amateur Radio Association website.

[Subscribe to our newsletter and get it delivered right to your inbox.]

The post National VOA Museum of Broadcasting Plans Anniversary Party appeared first on Radio World.

The author is membership program director of the National Federation of Community Broadcasters. NFCB commentaries are featured regularly at www.radioworld.com.

You can feel that crispness in the air. However, it is not just autumn. This time of year also brings the start of on-air fundraising season for community and noncommercial radio.

If you are a donor to or listener of your local community radio station, there is a good chance you are already aware of your area outlet’s endeavors. Check social media and you are likely to see an appeal to contribute today. When you tune in, you may hear a brief spot seeking phone volunteers or assistance with the pledge drive. Or maybe you even got a letter in the mail, reminding you of all the wonderful programming you enjoy and why your donation matters so much.

[Read: Community Broadcaster: Rain Down Reporting]

If you are not a regular community media consumer, you’ve probably heard of pledge drives at least. From parodies to tote bag references, noncommercial radio and television fundraising is just part of the media fabric. Even while there may be a disconnect as to why it is done, you just won’t find many people who have never heard of pledge drive, even if they have not given during one.

This season, the-Why-You-Should-Give is very important.

With all the conversation around news deserts, community radio nationwide fulfills a valuable role in the civic life of cities and towns everywhere. Music, arts, news, ideas and culture all find a place on community media in service to the greater mission of education. Your local station can only do this with your financial contributions.

Every state in the next 18 months will see major races for local, state and federal office as well as a list of referenda that may reshape communities for years to come. Community radio is there, providing coverage of, and sometimes hosting, candidate debates. Stations team up with city leaders for voter education and registration. These outlets cover the issues that matter to voters. Yet the coverage struggles to happen without listener support.

And lastly, community media creates opportunity in the local economy. Whether it may be through sharing a local music scene, collaborating with local businesses or making a city a better, more interesting place to live, stations create jobs, spur industry and enhance the quality of life everywhere. Think about it. When you think of Seattle, you probably are reminded of its iconic radio stations. When a fledging music scene is taking off, community radio may be the first place local bands and live event dates get heard. And surely no discerning music fan would ever deny that taste-making radio raises a town’s hip factor. Tis word of mouth means visitors, good word-of-mouth, and ultimately dollars locally.

Every community radio station needs financial support. A recent National Federation of Community Broadcasters survey indicates many community radio stations work with thin margins. This includes many having a small staff and few reserves. Given how far these mighty stations stretch dollars, the fact so many stations provide communities such unique programming and bold coverage is a minor miracle, frankly. However, the deep regard many community stations have for audience donations should hint at how much appreciate your help.

On-air fundraising is a time when listeners like you can ensure the voices you value and media you hope for in our vibrant democracy can have greater resonance. There is no better time than this lovely fall to be a first-time or repeat donor to a community radio station.

[Subscribe to our newsletter and get it delivered right to your inbox.]

The post Community Broadcaster: Community Radio Needs You appeared first on Radio World.

In Croatia in June, the World Broadcasting Unions’ Technical Committee supported the completion of standards associated with the European Broadcasting Union’s Technology Pyramid for Media Nodes.

“Broadcasters planning the move to new IP production facilities for television or radio should engage manufacturers with the Technology Pyramid for Media Nodes and ascertain their degree of compliance,” said Michael McEwen, head of the WBU Secretariat. “Further, the missing standards need to be completed as soon as possible so that broadcasters can make the important migration to IP with the required assurance.”

While the pyramid has clear relevance to the television industry, we share it because of the interest radio broadcasters have in the ongoing development of media IP. Radio World invited John C. Lee, P. Eng., chairman of the North American Broadcasters Association and World Broadcasting Union Technical Committees, to provide the background.

Click to Enlarge

In order to achieve the speeds and bandwidths of next-generation television systems, broadcasters are migrating from HD-SDI to IP-based technologies. In December 2017, SMPTE published the ST-2110 set of standards addressing “Professional Media over Managed IP Networks” to support this migration. This set of standards addresses precision system timing (PTP), video essence, audio, ancillary data, etc., in an IP environment.

In December 2018, the European Broadcasting Union (EBU) published the “Technology Pyramid for Media Nodes” (EBU Tech 3371). This pyramid includes all the necessary elements to design, build and operate a fully operational, interoperable, fully plug-and-play SMPTE ST-2110-based, live IP production facility. The EBU Pyramid includes all the needed protocols for timing and synchronization, configuration and monitoring, discovery and connection, media transport and security. It can be viewed as a broadcaster’s set of user requirements for a fully functional live IP production facility.

Along with SMPTE, other organizations have worked diligently to complete the various required protocols —  namely the Advanced Media Workflow Association (AMWA) and the Joint Task Force on Networked Media (JT-NM). AMWA first produced Networked Media Open Specification (NMOS) IS-04 addressing “Discovery and Registration.” IS-04 systems are intended to enable “zero-configuration” deployments, reducing the necessity to spend time manually configuring equipment before connection to the network. AMWA’s IS-05 addresses “Device Connection Management” which permits a control device to tell a receiver the stream it is supposed to take at any given time, a function analogous to routing.

JT-NM was tasked with addressing how all these standards and protocols (ST-2110, IS-04, IS-05, PTP, etc.) could fit together to build a complete live IP production system. TR-1001-1, entitled “System Environment and Device Behaviors for SMPTE ST-2100 Devices in Engineered Networks — Networks, Registration and Connection Management,” is the JT-NM’s first such technical recommendation and it aims to simplify the installation and configuration of SMPTE ST 2110-based facilities.

As more and more broadcasters begin to implement IP technologies in their production facilities, it is critically important that vendors address and implement all published standards and specifications in their shipped products. This will greatly alleviate the implementation challenges broadcasters will face. To this end, in April of this year, the EBU published R152 entitled “Strategy for the Adoption of an NMOS Open Discovery and Connection Protocol” to accelerate market adoption of these protocols.

In short, the EBU “Technology Pyramid for Media Nodes” describes a comprehensive IP ecosystem of protocols that empowers the design, implementation and operation of fully-IP production facilities.

The World Broadcasting Unions is the coordinating body for broadcasting unions that represent broadcaster networks across the globe. It was established in 1992. The North American Broadcasters Association acts as secretariat for the WBU. The unions that belong are the Asia-Pacific Broadcasting Union, the Arab States Broadcasting Union, the  African Union of Broadcasting, the Caribbean Broadcasting Union, the European Broadcasting Union, the International Association of Broadcasting and the North American Broadcasters Association.

The post About the EBU Media Technology Pyramid appeared first on Radio World.

Gospell’s IBC2019 is focused on unveiling five new products that all include DRM technology.

During a presentation at stand 3.C67 called “The Gospell Receiver—End to End Solution for Your Needs,” hosted by the DRM Consortium, Gospell debuted the products that are designed to be applicable to both the consumer and industry markets.

The products are the GR-22 portable DRM/AM/FM receiver; GR-227 DRM car adapter; GR-301 DRM/AM/FM monitoring receiver; GR-310 audio broadcasting monitoring platform; and the GR-AT3 high performance active HF antenna.

Gospell also discussed developments of digital radio in China during the presentation.

IBC Stand: 3.C67
Info: en.gospell.com

[Want more information like this? Subscribe to our newsletter and get it delivered right to your inbox.]

The post From IBC: Gospell Unveils New Products Featuring DRM appeared first on Radio World.

Making its debut at IBC, Axia Audio’s new Quasar console/control surface takes advantage of the flexibility afforded by IP networking and touchscreens.

Like many cutting edge consoles, Quasar relies upon an IP link, in this case Livewire, to an engine — acting more as a control surface. Much of this surface is occupied by an embedded central touchscreen. Physical faders flanking the screen are themselves surrounded by color OLEDs providing information and customizable functionality.

It will be available in sizes from 4 to 28 touch-sensitive, motorized faders per frame, with support for up to 64 faders in multiple linked frames. Frames can be flush-mounted.

Quasar can access and control inputs, hybrids, codecs and processing, etc., via Livewire, In addition it can be remote controlled via HTML5-compatible devices.

Quasar is powered by the all-new Quasar Engine, with 64 stereo channels, four-band fully parametric EQ, powerful dynamics processing and automixer on every channel, four program buses and eight auxiliary buses.

Axia says that Quasar was “designed based on extensive global customer feedback and ergonomic studies.”

IBC Stand: 8.D47

Info: www.telosalliance.com

The post IBC Sneak Peek: Axia Debuts Quasar appeared first on Radio World.

Wheatstone is showing its newly developed X5 FM audio processor front and center, which offers a slew of new technologies to help with dynamics control, pre-emphasis management and more.

These new technologies include the Limitless FM peak control that reconstructs audio after pre-emphasis has been applied for a cleaner and clearer high end. There’s also the X5’s Unified Processing technology that allows the processor to share critical information between all processing stages; it also features a redesigned limiter that works directly with the unit’s Limitless Clipper.

Additional features include the Live Logger to document X5 settings and activities; a redesigned bass processor and enhancement controls in the iAGC to safely equalize audio; an optional MPX SyncLink receiver that can work away from the studio and manage multiple HD and FM audio streams; and AES insert ports via a PPMport, allows users to insert ratings encoders into the processing system instead of placing it in front of the processor.

Previous features that have been updated in the new X5 model, like the Multipath Mitigation algorithm, composite processing system with selectable look ahead limiting or clipping, baseband192 composite AES connectivity and a full set of analysis displays.

IBC Stand: 8.C91

Info: wheatstone.com

[Want more information like this? Subscribe to our newsletter and get it delivered right to your inbox.]

 

The post Wheatstone Spotlights X5 FM Audio Processor appeared first on Radio World.

As part of its ongoing efforts to update its own application filing system, the Federal Communications Commission has transitioned a series of online applications from one database to another.

Starting Sept. 25, several applications will be transferred by the Media Bureau from the CDBS database to the LMS online electronic filing system. Seven application forms in total will be moved over, such as the construction permit application for commercial FM radio stations and the application requesting authority to construct/make changes to an FM translator station. See the complete list here.

Keep in mind that you’ll need to log into LMS using an FCC Registration Number  (FRN) and associated FRN password because — unlike the CDBS system — all filings in LMS are tied to a facility’s FRN. Also keep in mind that if a facility had multiple FRNs in the old CDBS system, a licensee will be asked to formally select one and only one of those FRNs the very first time they log into LMS.

The CDBS database will also no longer be the home for those looking to create a pleading or leave a comment. Instead, comments concerning applications filed using LMS must be filed using the LMS system.

The Media Bureau plans to transition more applications from LMS on an ongoing basis, the FCC said.

For assistance, contact the commission at 877-480-3201 (Option 2) or submit a request online here.

[Subscribe to our newsletter and get it delivered right to your inbox.]

 

The post Where Did Those Applications Go? Check the LMS appeared first on Radio World.

If you were to name a piece of broadcast equipment that is neglected, forgotten or taken for granted, the transmitter remote control would probably be high on the list. Nevertheless, remote controls have their own history, technological breakthroughs, pioneers and industry leaders.

The Moseley PBR-30 manual included this image detailing the lubrication points of stepping relays. Blended oil, watch oil and graphite oil were used at different points.

From the earliest days of broadcasting, many stations had a remote transmitter site, and FCC regulations of the day stipulated that an engineer with a First Class license be on duty at the transmitter during hours of operation. Their duties were to keep the transmitter log, taking required meter readings every 30 minutes, as well as maintaining the transmitter parameters within FCC regulations. That meant keeping power output within in a plus 5 and minus 10% window, carrier frequency +/- 20 cycles, and modulation between 85 and 100%. These are things we take for granted today, but they required continuous scrutiny in the early days of broadcasting.

Those early transmitters were prone to frequent breakdowns. Electronic components of the day were not that reliable, particularly when high voltage and RF were involved. An engineer had to be on site to make timely repairs.

With advances in technology, transmitters became more reliable. The FCC regulations remained in place, however, and the transmitter engineer’s unofficial duties often were extended to include bench repairs and maintenance of equipment, rewinding carts and dubbing agency spots.

FCC ACTION

Gradually, the driving forces for remote control of broadcast transmitters mounted, and change was in the air. But it didn’t happen overnight.

Harold Hallikainen, engineer for manufacturer QSC LLC, said the FCC’s rollout of remote control authorization spread slowly across the broadcast spectrum.

“In 1950, the FCC proposed authorizing remote control of Class D NCE FM stations, which had a power output of 10 watts or less. The foundations of subsequent rules can be seen in this first proposal,” he said. “Control circuit faults could not activate the transmitter, and any faults causing loss of on/off control would shut down the transmitter. No telemetry was specified. Since all comments were in favor, the rules were adopted.

“In 1952, the FCC discussed the possibility of remote control of non-directional AM stations and FM stations, both at or below 10 kW,” he continued. “The complicating factor of emergency frequency changes to comply with Conelrad requirements was also debated.”

In 1953, this authorization was granted. “Following a prolonged comment period, the commission authorized remote control of high-power and directional radio station in 1957. Television had to wait even longer. UHF stations were authorized in 1963, VHF in 1971.”

Radio broadcasting has long borrowed hardware and technology from the phone company. When engineers began to envision how a transmitter remote control would work, stepping relays were the logical choice. As the foundation of the rotary-dial telephone system, a stepping relay was basically a pulse-driven, multiple pole 1 x 10 switching matrix.

As manufacturers designed the first remote controls in the mid-1950s, basic elements began to emerge: a studio and transmitter unit, each with a four-pole stepping relay. One pole was for metering +, one for metering –, a third for raise functions and the fourth for lower functions.

Connection between the studio and transmitter units was by two phone lines, each with DC continuity. One was for metering, the other control. Both wires in the control pair worked against ground in a “simplex” arrangement, providing two independent control circuits. A DC voltage generated at the studio usually held in a relay at the transmitter side that controlled plate on/off, fulfilling the FCC requirement for fail safe.

All these systems had calibration pots on the transmitter side for each channel. When the engineer made the FCC-required weekly calibration of the remote control, he would call the studio and the operator would give the local meter readings. The engineer would adjust the calibration pots so the remote meters agreed with the transmitter readings. There was also a single calibration control on the remote unit, which was used to compensate for changes in loop resistance of the phone line, which varied as a function of temperature and humidity.

AUDIO TONES

One of the pioneers in remote control systems was the Rust Industrial Co. Inc. of Manchester, N.H. Founded in 1954 by W.F. Rust Jr., it also introduced a strip chart recorder for transmitter logging in 1958 and its advanced AUTOLOG product line in 1964. The company moved to Cambridge, Mass., and later Everett, Mass.; it appears to have gone out of business in 1974.

The Gates RDC-10AC is typical of first-generation remote controls, with 10 metering/control channels accessed by stepping relays in the studio and transmitter units. Two phone lines with DC continuity were required for control and metering.

Gates also got in the game early with its popular RDC-10AC, as well as the long-forgotten RCM-20, which worked with audio tones rather than DC voltages, an innovative approach in 1955.

A 10-channel remote control was adequate to control two transmitters, but when large directional arrays were involved, or later, television transmitters, something more robust was called for. Gates introduced the RDC-200, which added three more stepping relays to provide 39 channels, and used a rotary telephone dial to access them. Other manufacturers developed similar offerings.

With some refinements to the metering and control circuits, this stepping relay infrastructure would be integral to most remote control systems for the next 20 years. These relays were not without their issues, however. The combination of rapidly turning the selector switch and a high-capacity phone line could cause the studio and transmitter steppers to get out of sync, resulting in erroneous readings. Stepping relays also required regular maintenance for reliable operation. That included lubricating wiper contacts and moving parts.

Moseley Associates was one of the first companies to embrace digital techniques in the design of remote controls. Its PBR-15 and -30, introduced in 1970, eliminated the stepping relay from the studio end. In place of the traditional 10-position rotary switch for channel selection was a ganged 16-position (on the PRB-15) push button switch. Binary numbers were generated by the push button assembly. They were then encoded to the stepper drive generator.

Control functions were handled by a 920 Hz audio signal that was briefly interrupted to send pulses to the stepping relay at the transmitter. Different tones were added to the 920 Hz for raise and lower. Metering signals were generated by applying the sample signal to a voltage controlled oscillator.

Introduced in 1975, the Moseley TRC-15 used digital techniques to eliminate stepping relays.

The successor to Moseley’s PBR-15 was the TRC-15, introduced in 1975. The PBR and TRC looked identical, but the TRC performed all control functions using frequency-shift keying technology. It also eliminated the troublesome stepping relay from the transmitter end. A control demodulator with SN74154 decoders and 7404 hex inverters connected to an individual relay for each of the 15 channels.

NEW OPTIONS

These Moseleys and other audio-based control systems had the advantage of needing only one phone line, resulting in an immediate reduction in operating costs. But there were far more important benefits to these new systems.

Once audible or subaudible tones were used for control and metering, several options became available for interconnecting the studio and transmitter units. In addition to traditional phone lines, there was the possibility of audible control over internal 110 kHz subcarrier generator and demodulator. Usually these signals rode from the studio to transmitter piggyback on the STL link. Subaudible metering returns in the 20–30 Hz range could be accomplished on FM stations via an SCA channel, which could also be used for background music or other programming. For AM operations, the subaudible metering signal was returned on the AM carrier. Modulation of the subaudible tones was set to around 5%.

Gradually, Moseley gave remote control circuitry a complete makeover, using TTL logic circuits, voltage controlled oscillators and other digital techniques. The one remaining weak link was the analog panel meter. Offset and gain drift were constant. Checking the zero set and CAL adjustments before taking a set of readings was mandatory. The analog meter precluded using the Moseley for any of the automated control and metering systems that were beginning to emerge. Also, the numerous scales on the meter could be confusing to non-technical operators.

In 1977, the Moseley TRC-15 and PBR-30 remote controls finally got digital panel meters. But they didn’t come from Moseley, rather from a small startup company just down the road from the remote control manufacturer.

Harold Hallikainen’s company, Hallikainen & Friends, developed the TEL 171 to meet this need. The genesis of the TEL 171 was really an FCC inspection at a station where Hallikainen was chief engineer.

Hallikainen & Friends’ TEL 171 gave the Moseley TRC-15 remote controls a digital panel meter and enabled remote control of a transmitter via the DB-25 connector.

“The inspector dropped our Bauer 707 from 1 kW to 250 W, and asked the operator for the readings,” he said. “The operator read the wrong scale and gave the 1 kW readings, since everything doubled going from 250 W to 1 kW. This incident, the difficulty of calibration and misplaced decimal points were the things that inspired me to design the TEL 171.”

He adds, “It originally did not have a display at the transmitter site. KCBS said they’d buy one if  we could make that happen. There was not enough power available to run an LED display off of the floating power supply. Around that time, the DF 411 chip was introduced. That made it easy to drive an LCD, so that was used for the transmitter display.” Hallikainen doesn’t recall exact numbers but estimates that a few thousand TEL 171s were sold.

The TEL 171 could be more than a digital display option. A DB-25 connector located below the display made available binary-coded channel select lines, raise-lower functions and the multiplexed BCD reading. Bill Bordeaux of Interstellar Engineering designed the ITO-177 (Intelligent Transmitter Operator). It plugged into a Commodore 64, and made the TRC-15A/TEL-171 controllable via BASIC programming.

SMOOTH UX

Other manufacturers were bringing digital to their remote controls, and had a different approach than Moseley. TFT introduced the model 7601 in 1982. It used FSK modems on each end. The Harris 9100 fully embraced the then-new FCC ATS rules enabling unattended operations. The emphasis was shifted from remote control of transmitters to facilities control. The logging software included trend analysis, enabling users to locate problems areas and anticipate failures.

Throughout the 1970s, Moseley had been the innovator in remote control technology and had the high end of the remote market to itself. When Gentner came on the scene, it changed the game with its VRC-1000.

Utilizing the DTMF tones from a phone, along with speech synthesis, Gentner eliminated the studio side of the remote control. All that was needed was to dial the site, enter the password and follow the menu options. It also meant the transmitter could be controlled from anywhere. The issue of how to accomplish the fail safe was resolved with a silence sensor. The concept of telephone access was developed by John Leonard of Moseley, who later sold the design to Gentner.

Microprocessors arrived in the early 1970s, powering the first generation of personal computers. Soon, they were being embedded in various electronic devices.

In 1980, Moseley introduced the MRC-1, the first microprocessor-based remote control, using an 8-bit Motorola 6802. It comprised one control terminal and up to nine remote terminals. Each remote site had 32 channels available. Alarm parameters could be created for each channel, and an automatic logging option enabled regular printout of transmitter logs. A CRT option duplicated all the functions of the MRC-1 control panel, and could simultaneously display data from all 32 channels at one site.

The Burk Technology ARC Plus Touch is an IP-based remote control that uses a combination of distributed I/O connections and an integrated SNMP manager. Up to 256 channels of metering, status and control are possible.

The coming of the internet was another game-changer for remote control technology. But as Peter Burk, president of Burk Technologies recalls, the rollout was rather protracted.

“In the early days of the internet, it could be difficult to get a connection to a remote transmitter site. Two solutions emerged, an Intraplex connection, or alternatives such as cellular modems, licensed and unlicensed wireless and satellite.”

Burk’s first internet-based remote control was the ARC-16, which was able to control multiple transmitter sites. Even more impressively at the time, the system enabled site-to-site control.

As with much of broadcast technology, the cutting edge for remote controls largely has shifted away from circuit cards in rack-mounted boxes to software running on PCs. Burk’s Auto Pilot enables multi-site, PC-based facilities management for Burk remote controls. The interface is customizable, and reports can be tailored. They can be printed automatically or emailed as a PDF to station personnel. AutoPilot includes network management functionality, bridging the gap between broadcast and IT by including SNMP and ping with traditional I/O.

AutoPilot with Warp Engine provides a customized real-time view of the entire broadcast plant, monitoring up to hundreds of sites at the same time from one PC, using minimal bandwidth.

The remote control segment has always been specialized. Ask an equipment dealer today and they’ll tell you about options from companies like Burk, Davicom, WorldCast Systems, Broadcast Tools, Broadcast Devices, Sine Systems and CircuitWerkes.

So what’s in the future for broadcast remote controls? Right now, the greatest force driving innovation seems to be artificial intelligence, although Peter Burk prefers the term machine learning.

“Our goal is to look at the wealth of data that is now available at a transmitter site and deliver predictive analytics. For example, assume your transmission line has developed a small leak, but the nitrogen tanks are keeping up with it. If you check the pressure, it will be OK. If the sensors are tracking the flow, however, they will see an increase. In this case, we would want the software to give you an alert to check the system before the nitrogen runs out and you have an emergency.”

Another trend is to understand that the remote control is now a part of the Internet of Things; equipment users and designers plan accordingly.

“One of the challenges is that IoT generates an enormous amount of information, and we need to find a better way to reduce this data down to actionable information,” he said.

Burk adds that human access to the IoT raises some interesting challenges. “Alexa and other smart speaker technologies bring with them the promise of the voice-activated Internet, as well as  the challenge of building seamless interfaces. At the same time, accessing IoT via the screen of mobile devices is exploding, and the need for a smooth UX or user experience is paramount.”

Tom Vernon is a longtime contributor to Radio World. Comment on this or any story. Email radioworld@futurenet.com with “Letter to the Editor” in the subject field.

The post Remote Controls Have a History All Their Own appeared first on Radio World.

North Korea has returned to digital radio broadcasting after an absence of nearly two years.

The latest Digital Radio Mondiale (DRM) shortwave transmissions began mid August. The country has had periodic DRM broadcasts for many years.

A screenshot showing North Korea using a Dream DRM transmitter modulator. Credit: Hans Johnson

It appears unclear at this time however whether the current series of transmissions will soon end or be the start of a regular service.

Thus far, all of the latest test transmissions have taken place on 3560 kHz, which is actually allocated for amateur radio use.

According to radio enthusiasts in the region, the signal has been clear and very audible.

In 2012, 2016, and 2017, the country’s international service, The Voice of Korea, trialed DRM.

Those tests involved a professional grade DRM modulator, which identified itself as being from the Engineering Research Center of Digital Audio and Video (ECDAV) at the Communications University of China in Beijing.

Pyongyang Broadcasting Station, a Korean-language service for Koreans living in China, Japan, and South Korea, has been carrying out these latest broadcasts, which appear to implement two DRM modulators.

The image shows North Korea using a professional DRM modulator made by BBEF. Photo credit: Hans Johnson

Based on settings and parameters, the first is the open-source, software-based Dream DRM transmitter.

Developed at Germany’s Darmstadt University some 15 years ago, technicians continue to tweak various parameters, such as bandwidth, as they test and learn about the system.

In spite of its age, the Dream DRM transmitter is compatible with any DRM receiver. North Korea could easily put on multiple DRM transmitters using this free system.

North Korean operators also appear to be using a professional grade DRM modulator, which is most likely from private Chinese manufacturer Beijing Broadcasting Equipment Factory (BBEF). BBEF is best known for selling North Korea a number of shortwave transmitters ranging in power from 20 to 150 kW in 2011.

A professional DRM modulator is more capable than Dream. But North Korea probably cannot manufacturer its own and a single modulator can easily cost many thousands of dollars.

A lot has changed since North Korea last aired DRM broadcasts two years ago. Broadcasters in China and Guam have started regular DRM services and Russia is set to begin a service for Russia Far East.

With so many DRM programs coming on air in the region, North Korea may finally decide to remain on the air for good using the digital radio standard.

The post North Korea Resumes DRM Broadcasts appeared first on Radio World.

“Best of Show Up Close” is a series about participants in Radio World’s annual Best of Show at NAB Awards program.

MaxxKonnect nominated the MaxxKonnect Wireless LTE  internet link. MaxxKonnect Wireless acts as reliable link for remote productions or remote sites. It is designed to work right out of the box. MaxxKonnect has negotiated priority service deals with AT&T and Verizon to ensure service throughout most of the country.

We asked MaxxKonnect President and CEO Josh Bohn for more information.

Radio World: What is MaxxKonnect?

Josh Bohn: MaxxKonnect Wireless is prioritized LTE internet service designed for broadcast applications. We work on the Verizon and AT&T networks (T-Mobile is coming soon) which gives us the flexibility to give customers the carrier which works better in their area. Each one of our SIMs comes with priority on the carrier network, plus a true public static IP address, which is crucial for most broadcast applications.

RW: What inspired its creation?

Bohn: Back in 2014, I had a group of stations I was taking care of. I had one station out in the woods, about 14 miles from the nearest cell tower — and two and half hours from my house. The phone company couldn’t even keep a landline into it. So, it would go off the air, someone would call me and say it was off and I’d call the remote. This call was answered by a “this line is currently out of service” message, which was followed by me cussing for a bit, then making the long drive out to the woods. I’d arrive, push Plate ON on the transmitter, cuss at is some more, then drive back. A five-hour round tripper to literally push a button. After about the umpteenth time, I finally said, “There has to be a better way …”

[Read: Best of Show Up Close: Davicom Cortex 320]

We tried a regular LTE wireless modem and SIM into a Cradlepoint router, which is a fairly standard setup. This succeeded in getting an internet connection into the place, albeit with some external antennas. But it still wasn’t very good. And since there wasn’t a static IP — or even a public IP — we had to resort to a PC at the site and LogMeIn for any kind of site control or monitoring. This setup worked, but was clunky. The PC would update and cause problems, or wouldn’t reboot after a power fail, etc., etc. It was during this stage that I started negotiations with the carriers for what would become MaxxKonnect.

Once I was able to successfully negotiate our service with the carriers, we beta tested for over three years before ever introducing the product to the market. I wanted to be 100% confident that this service would be reliable and robust for broadcasters in as many areas as possible. We debuted it at NAB2018 as an aside to our main showing (which flopped, BTW). It caught the eye of Chris Tobin and Kirk Harnack. Since then, our user base has been steadily growing.

RW: What kind of questions did booth visitors ask about MaxxKonnect?

Bohn: The thing we heard the most was, “You can’t do this. This won’t work.” Well, I assure you, yes we can do it — and yes, it does work! People were somewhat skeptical of the priority part of the service, but we’ve got lots of test cases to prove it. Another was, “Well, I can get this from Verizon or AT&T tomorrow.” No, unfortunately you can’t. This service took me years to develop and isn’t available to the average person.

People also asked about the commitment. That’s one of the cool things — there is no commitment! If you get the service, try it and decide for whatever reason you don’t want it anymore, you can cancel! No fees, no arguments, no transferring between 12 departments. Just give us 30 days’ notice and pay your last bill — and that’s it. And we all stay friends. My goal for this was to make it easy for broadcasters to get the connectivity they needed for transmitter sites, remotes, etc.

They also asked about hardware. We do offer hardware from Cradlepoint and Pepwave, depending on your needs. A lot of customers like that they can order a complete package from us. When it arrives, it’s already programmed and setup, so all the customer has to do it take it out of the box, plug it in and — Voila! — they have internet. But, another cool feature is that our service is compatible with basically any LTE data hardware! Whether it’s a Comrex Connect modem, a Tieline modem, a Pantech modem or a Cradlepoint — MaxxKonnect works with it. As long as you can change the APN information to our private and/or semiprivate APN, you can use any hardware. We are currently testing with smart devices (phones, tablets, etc.) for data use with no voice or text/SMS. Preliminary tests show promise for use with audio programs like LuciLive, Skype and others. This would simplify remotes even more for some customers.

We’ve also got a POTS replacement service we’re starting to roll-out called MaxxPhone. It’s a low-cost way to get a POTS line for your remote control via your MaxxKonnect internet connection.

RW: Who would use MaxxKonnect?

Bohn: Anyone that needs internet service, basically! MaxxKonnect is usually deployed at remote sites where traditional internet delivery isn’t an option, and for remotes. The priority on the network is key for remotes with large crowds of people. It cuts through all the bandwidth clutter and lets your broadcast continue when 15,000 people show up with their 1.5 devices each. I’ve also got customers who are using it as a backup to their IP radio system at their transmitter sites; others who are using it as an emergency backup at their studios to keep their IP phone systems alive when their main internet fails; and others using it as primary STLs with their favorite hardware codec. A MaxxKonnect is an extremely useful tool to have around your station for all kinds of solve all kinds of connectivity needs!

RW: Why would someone use MaxxKonnect when wireless service is available everywhere?

Bohn: We get asked this a lot. Think of it this way — when you show up to a concert or a fair or a race or whatever, and you try to do something on your phone, what happens? Typically nothing. The cell towers or the venue Wi-Fi is so overloaded with everyone doing Facebook Live, Instagram, etc., that you can’t even load a web page, let alone do a broadcast. The prioritization of the MaxxKonnect service puts your connection on a different part of the carrier network, which bypasses all of the congestion in the public space, and lets you connect to do your broadcast reliably. Now, we can’t guarantee anything 100% — no one can. Internet and carrier anomalies do happen. We’ve had a few places (mostly in extremely rural parts of New England) where the service just won’t work because the carriers never built out the back end. In those cases, the customer just sent their router back and we refunded them. But, the MaxxKonnect service has been successfully used multiple times at major music festivals around the country, as well as concerts, SEC football games, the Regions Tradition golf tournament, major fairs and the Indianapolis 500 (with their 300,000+ attendees.)

RW: How much does MaxxKonnect cost? Is there a service fee?

Bohn: Yes. The monthly cost varies based on the amount of data you expect to need. We can do a 1 GB plan for as low as $56 and go all the way up to 100 GB plans. Our most popular plans are 10 GB. These range from $109 per month to $129 per month, depending on the carrier. Another awesome feature of the MaxxKonnect service is if you hit your “data cap,” nothing happens to your data stream. We won’t throttle you or turn you off. You just get billed for the overage. Broadcasters need reliability and known connectivity, not another headache of wondering if their station or broadcast is going to go off because they exceeded their data cap.

Also, if you purchase multiple plans on the same tier on the same carrier, their data pools together into on big “data bucket.” For example, if you get six 10 GB plans on Verizon for your company or station, you don’t have six individual 10 GB devices which are subject to overages after 10 GB. You’ve actually got 60 GB of total data that can be used across all of the devices. If one device uses 45 GB and the others each use 2 GB, you’re still under your cap. It’s great way to maximize value for a large scale deployment across a company or group.

RW: What does MaxxKonnect consist of?

Bohn: MaxxKonnect is a service primarily. You must get the MaxxKonnect SIM from Bohn Broadcast — you can’t get this directly from the carriers. MaxxKonnect becomes your ISP. You need some type of compatible hardware — which can be provided by the customer or by us. And that’s really it. It’s very simple from a deployment standpoint.

RW: Is there a 5G version in the works?

Bohn: Most likely, yes. We are currently able to achieve the reliability that we need using the existing 4G LTE technology. However, as 5G continues to roll out, our service will continue to evolve to utilize new technology to maintain our necessary level of reliability.

The Future Best of Show Awards program honors and helps promote outstanding new products exhibited at industry conventions like the spring NAB Show. Exhibitors pay a fee to enter; not all entries win. Watch for more coverage of participating products soon. To learn about all of the nominees and winners, read the 2019 Best of Show Program Guide.

The post Best of Show Up Close: MaxxKonnect Wireless appeared first on Radio World.